
No grout, no thresholds, no transition strips between rooms. One continuous surface running from the entry through the kitchen to the glass, applied over the slab or tile that is already there.
Tile is a grid. However large the format, the eye reads a repeating unit and a joint, and the joint chops the room into pieces. Microcement has no unit and no joint, so the floor reads as one plane and the room reads as one room.
That is not only aesthetic. A continuous floor is the single cheapest way to make a South Florida house feel larger, because the thing that makes an open plan feel closed is the threshold strip between the kitchen and the living area and the change of material on either side of it.
It goes down over what is there. An existing tile floor or a bare slab both work as substrate, which means no demolition, no dumpster, and no week of jackhammering before anything starts. Total build is a few millimeters, so door clearances and appliance heights barely move.
It works with underfloor heating, it takes any color, and because it is troweled by hand it carries real movement across the plane rather than the printed repeat you get on large format porcelain.
Entry, hallway, kitchen, living, all one surface. No metal strip, no change of height, nothing to catch a toe or a chair leg on.
Nothing to darken in a high traffic line, nothing to seal every couple of years, nothing that makes a clean floor still look dirty along the walkways.
No demolition phase, which on a whole floor is the difference between a two week job and a six week one, and the difference between living in the house and moving out.
No demo crew, no flooring installer, no transition carpentry. Michael quotes it and Michael applies it.
Whole-floor work is where the no-demolition argument stops being a nice feature and starts being the reason the project happens at all.
Most floor projects start with the public rooms and the hallways, because that is where the thresholds are most obvious.
The main case. Kitchen, dining and living running together with nothing to mark where one ends.
Including under and around islands, with the floor continuing unbroken to the cabinet toe kick.
The highest traffic surface in the house and the one where tile grout shows wear first.
Treads, risers and landings in one finish, with no nosing trim and no carpet edge.
Quieter underfoot than tile and warmer to the touch, and it continues from the hallway with no threshold.
Specified with an exterior-rated sealer for sun, rain and salt air.
A floor is usually specified alongside the bathrooms, because the same crew is already in the house.
No demolition, no new substrate, no tile torn out. Microcement applied directly over the floor that was already there.
Drag the handle, or use the left and right arrow keys.
The calculator asks for square footage and which surfaces you are doing, then emails you a real range in about a minute. Whole floors are where it is most useful.
No stock imagery, no renders, no borrowed portfolio. These are South Florida homes Michael finished himself.





Monarch was founded by Michael Daniels, a U.S. Marine Corps veteran and one of the first certified ForCrete installers in the country. He trains new applicators for ForCrete Americas, and he leads every Monarch project personally alongside a crew he trained himself.
A whole floor is unforgiving, because any variation in the plane shows up across thirty feet of surface in raking afternoon light. Getting that flat is the job. He lives in Deerfield Beach and works from Miami up through Palm Beach, and when you call, you talk to him.
Book a free consultationFloors are quoted on square footage and on the condition of what is under them. A bare, level slab is the straightforward case. An existing tile floor with drummy areas takes more prep hours before the primer goes down, and that shows up in the quote as prep rather than as a surprise.
Whole-floor work is where the per-foot rate matters most, because the area is large. The calculator on the home page gives you a real range in about a minute and emails you the breakdown so you have it in writing.
There is a calculator on the home page that gives you a real range in about a minute, and it emails you the breakdown so you have it in writing. It is a range, honestly labeled as one. The firm number comes after somebody stands in the room.
Per square foot of total surface area. On a whole floor this is the number that decides the project.
The existing floor stays. No dumpster rental, no debris haul, no week of labor to pay for.
Typical time on site for all the floors in a home. A whole home including bathrooms is 2 to 4 weeks.
In most homes, yes, and that is the usual way we do it. The tile stays where it is. Reinforcing mesh and two sanded base coats bring the whole area to one plane before color goes down, so the grout lines do not telegraph back through.
Yes. The system is compatible with underfloor heating, and because it is only a few millimeters thick it transfers heat more readily than a tile and thinset build. Tell us at the consultation so the specification accounts for it.
Not in a normal interior finish. Floors are sealed with a different product from the polished one used on walls, and for wet areas and exterior terraces we specify a textured sealer with more grip. That gets decided at the sample stage.
The system we install is epoxy-based with very high tensile and compression strength, so it handles normal traffic, furniture and pets. Dragging something heavy and gritty across it can mark the sealer, which is refinishable in place rather than requiring replacement.
The day after the final coat. Wet areas are ready about a day after the last coat as well. The whole floor is typically 8 to 12 days on site for a full home, and there is no demolition phase to live through first.
Floor, wall and ceiling installations typically run $18 to $24 per square foot of total surface area. Whole-home packages covering floors, walls and bathrooms commonly run $30,000 to $80,000 and up depending on size and scope. You get exact numbers after a short consultation.
Answer a few questions about the space, then pick a time. Thirty minutes on the phone with Michael, who gives you real numbers rather than a guess.
Michael is based in Deerfield Beach and runs every project personally. Pick your city for the neighborhoods we cover and the work we have done there.
Not on the list? Ask. If it is between Miami and Stuart the answer is almost always yes.
We also do Venetian plaster, microcement over tile, showers and bathrooms and countertops.
Tell us about the floors and pick a time. Thirty minutes on the phone with Michael, who will ask what is down now and give you a realistic range on the call. Nothing is booked until he has seen the surface in person, and that visit costs nothing either.
Tell us about your space Get a ballpark firstOr call and text (561) 288-2474